 speed auto
!
interface GigabitEthernet0/1
 no ip address
 duplex auto
 speed auto

R1#outer ospf 7
         ^
% Invalid input detected at '^' marker.
	
R1#router o
          ^
% Invalid input detected at '^' marker.
	
R1#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#interface Serial0/0/0
R1(config-if)#
R1(config-if)#exit
R1(config)#interface Serial0/0/0
R1(config-if)#no 195.29.1.1 255.255.255.0
                 ^
% Invalid input detected at '^' marker.
	
R1(config-if)#no 195.29.1.0 0.0.0.255
                 ^
% Invalid input detected at '^' marker.
	
R1(config-if)#router ospf7
              ^
% Invalid input detected at '^' marker.
	
R1(config-if)#exit
R1(config)#router ospf7
                      ^
% Invalid input detected at '^' marker.
	
R1(config)#router ospf 7
R1(config-router)#no network 195.29.1.0 0.0.0.255
% Incomplete command.
R1(config-router)#no network 195.29.1.1 255.255.255.0
% Incomplete command.
R1(config-router)#
R1(config-router)#exit
R1(config)#exit
R1#
%SYS-5-CONFIG_I: Configured from console by console

R1#sh r
Building configuration...

Current configuration : 808 bytes
!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname R1
!
!
!
!
!
!
!
!
no ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO2901/K9 sn FTX1524ECA1-
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!
!
!
!
!
!
interface GigabitEthernet0/0
 ip address 195.29.1.1 255.255.255.0
 duplex auto
 speed auto
!
interface GigabitEthernet0/1
 no ip address
 duplex auto
 speed auto
 shutdown
!
interface Serial0/0/0
 ip address 195.29.12.1 255.255.255.252
!
interface Serial0/0/1
 ip address 195.29.13.1 255.255.255.252
 clock rate 2000000
!
interface Vlan1
 no ip address
 shutdown
!
router ospf 7
 log-adjacency-changes
!
ip classless
!
ip flow-export version 9
!
!
!
!
!
!
!
!
line con 0
!
line aux 0
!
line vty 0 4
 login
!
!
!
end


R1#
R1#
R1#
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#enable
% Incomplete command.
R1(config)#
R1(config)#exit
R1#
%SYS-5-CONFIG_I: Configured from console by console

R1#enable
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)# router ospf 7
R1(config-router)#195.29.1.0 0.0.0.255 area 0
                  ^
% Invalid input detected at '^' marker.
	
R1(config-router)#network 195.29.1.0 0.0.0.255 area 0
R1(config-router)#network 195.29.12.0 0.0.0.3 area 0
R1(config-router)#network 195.29.13.0 0.0.0.3 area 0
R1(config-router)#router ospf 7
R1(config-router)#passive g0/0
R1(config-router)#end
R1#
%SYS-5-CONFIG_I: Configured from console by console

01:33:11: %OSPF-5-ADJCHG: Process 7, Nbr 195.29.23.1 on Serial0/0/0 from LOADING to FULL, Loading Done









R1 con0 is now available






Press RETURN to get started.




Copyright (c) 2010 by cisco Systems, Inc.
Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
CISCO2901/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled

Readonly ROMMON initialized

program load complete, entry point: 0x80803000, size: 0x1b340
program load complete, entry point: 0x80803000, size: 0x1b340

IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x3bcd3d8
Self decompressing the image :
########################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
                  TYPE      MEMORY_REQ
           HWIC Slot 0      0x00200000     Onboard devices &
          buffer pools      0x0228F000
-----------------------------------------------
                TOTAL:      0x02A8F000
Rounded IOMEM up to: 44Mb.
Using 6 percent iomem. [44Mb/512Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 18-Jul-07 04:52 by pt_team
Image text-base: 0x2100F918, data-base: 0x24729040

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco CISCO2901/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FTX152400KS
2 Gigabit Ethernet interfaces
2 Low-speed serial(sync/async) network interface(s)
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)


         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R2
R2(config)#
R2(config)#
R2(config)#
R2(config)#hostname Router2
Router2(config)#
Router2(config)#
Router2(config)#
Router2(config)#enable
% Incomplete command.
Router2(config)#config t
%Invalid hex value
Router2(config)#int g0/0
Router2(config-if)#ip add 195.29.2.1 255.255.255.0
Router2(config-if)#no shutdown

Router2(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router2(config-if)#int s0/0/0
Router2(config-if)#ip add 195.29.12.2 255.255.255.252
Router2(config-if)#no shutdown

Router2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

Router2(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router2(config-if)#int s0/0/1
Router2(config-if)#ip add 195.29.23.1 255.255.255.252
Router2(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
Router2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up









Router2 con0 is now available






Press RETURN to get started.













Router2>








Router2 con0 is now available






Press RETURN to get started.













Router2>enable
Router2#config t#
                ^
% Invalid input detected at '^' marker.
	
Router2#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router2(config)#router ospf 7
Router2(config-router)#network 195.29.2.0 0.0.0.255 area 0
Router2(config-router)#network 195.29.12.0 0.0.0.3 area 0
Router2(config-router)#
01:32:48: %OSPF-5-ADJCHG: Process 7, Nbr 195.29.13.1 on Serial0/0/0 from LOADING to FULL, Loading Done

Router2(config-router)#network 195.29.23.0 0.0.0.3 area 0
Router2(config-router)#router ospf 7
Router2(config-router)#passive g0/0
Router2(config-router)#end
Router2#
%SYS-5-CONFIG_I: Configured from console by console



-----------------------------------------------
                TOTAL:      0x02A8F000
Rounded IOMEM up to: 44Mb.
Using 6 percent iomem. [44Mb/512Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 18-Jul-07 04:52 by pt_team
Image text-base: 0x2100F918, data-base: 0x24729040

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco CISCO2901/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FTX152400KS
2 Gigabit Ethernet interfaces
2 Low-speed serial(sync/async) network interface(s)
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)


         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname "hostname R3"
% Spaces are not allowed in hostname
Router(config)#
Router(config)#hostname "hostname R3"
% Spaces are not allowed in hostname
Router(config)#
Router(config)#hostname "hostname R3"
% Spaces are not allowed in hostname
Router(config)#
Router(config)#hostname "hostname R3"
% Spaces are not allowed in hostname
Router(config)#
Router(config)#hostname "hostname R3"
% Spaces are not allowed in hostname
Router(config)#
Router(config)#hostname "hostname R3"
% Spaces are not allowed in hostname
Router(config)#
Router(config)#hostname R3
R3(config)#
R3(config)#








R3 con0 is now available






Press RETURN to get started.













R3>
R3>enable
R3#config t
Enter configuration commands, one per line.  End with CNTL/Z.
R3(config)#int g0/0
R3(config-if)#ip add 195.29.3.1 255.255.255.0
R3(config-if)#no shutdown

R3(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

R3(config-if)#int s0/0/0
R3(config-if)#ip add 195.29.13.2 255.255.255.252
R3(config-if)#no shutdown

R3(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

R3(config-if)#int s
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

               ^
% Invalid input detected at '^' marker.
	
R3(config-if)#int s0/0/1
R3(config-if)#ip add 195.29.13.2 255.255.255.252
% 195.29.13.0 overlaps with Serial0/0/0
R3(config-if)#int s0/0/1
R3(config-if)#ip add 195.29.23.2 255.255.255.252
R3(config-if)#no shutdown

R3(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
exit
R3(config)#exit
R3#
%SYS-5-CONFIG_I: Configured from console by console









R3 con0 is now available






Press RETURN to get started.













R3>enable
R3#config t
Enter configuration commands, one per line.  End with CNTL/Z.
R3(config)#router ospf 7
R3(config-router)#network 195.29.1.0 0.0.0.255 area 0
R3(config-router)#network 195.29.13.0 0.0.0.3 area 0
R3(config-router)#network195.29.23.0 0.0.0.3 area 0
                         ^
% Invalid input detected at '^' marker.
	
R3(config-router)#network 195.29.23.0 0.0.0.3 area 0
R3(config-router)#router ospf 7
R3(config-router)#paassive g0/0
                    ^
% Invalid input detected at '^' marker.
	
R3(config-router)#end
R3#
%SYS-5-CONFIG_I: Configured from console by console

